JC-22D Draft Controller
The JC-22D Draft Monitor and Controller is a microprocessor based draft controller, indicating instrument, and alarm monitor. The JC-22D includes advanced control algorithms for tall stacks, multiple furnace stacks, and fast varying loads.
Uncontrolled stack draft can cause burner instability, unreliable ignition, and affect fuel-air ratio control repeatability. Burner manufacturers typically recommend draft controls be installed in applications where:
• Stack height exceeds 75 feet
• Multiple furnaces are connected to a single stack
Power Supply: 120 VAC, +/- 15%, 50/60 Hz, 15 VA
Case Size: 8" H x 3.5" W x 7.5" D
Enclosure Type: NEMA 4 faceplate
Ambient Temp.: +32° to 122° F
Displays: High Contrast LCD Display
4" high, 0.5% Resolution Bargraph
Bargraph Range: -1.00 to +1.00" W.C.
Alarm Setpoints: One (1) adjustable contact with
adjustable time delay
Draft Input: 4-20 mADC digital filtered
Firing Rate Input: 300 ohm (minimum) or 4-20 mADC
Discrete Input: Five, Optically isolated 120 VDC, 10 mA load
Actuator Feedback: 300 ohm min feedback pot
(required for GAP PID Control Mode)
Relay Outputs: Three SPDT Relays 10 A Resistive,
8 FLA, ½ HP, 120 VAC
Actuator Outputs: One Triac pair, 2 FLA/24-120 VAC
or 4-20 mADC
Network: 1200 - 38400 Baud; RS485
Modbus, ASCII or RTU
Provide a self contained automatic sequence draft controller for each furnace. The controller shall be microprocessor-based and suitable for flush, panel mounting. Provide a field mountable 4-20 mADC pressure draft transmitter for measuring boiler outlet draft. Provide a high flue gas pressure (low draft) switch with 5 second delay for use in the Flame Safeguard Limit Circuit.
2. Draft Controller
The Controller shall continuously indicate furnace draft, draft setpoint and alarm setpoint on a highly visible backlit LCD display. The control shall provide both automatic and manual damper control. Provide an integral or separate 4", 0.5% resolution (minimum) bargraph display in engineering units with visual alarm indication. Provide a “High Boiler Pressure” alarm, “Alarm Silence” pushbutton and one 10 A alarm relay output. The housing shall be panel mountable, fully gasketed with NEMA 4 front face. All adjustments shall be made from the front panel display in engineering units. The controller shall include setup menus for easy operation, tuning and troubleshooting from the Controller faceplate. No external configuration tools shall be required.
3. Automatic Draft Sequence
The controller shall include an automatic draft sequence as follows: during burner “off” periods the draft control damper shall remain closed to hold residual heat within the boiler. On a call for burner operation the outlet damper shall be driven open for pre-purge. To prevent pressurizing the boiler, the burner fan shall start after a field adjustable time delay after starting to open the draft damper. The damper shall remain open for burner light-off. When the fuel valve opens, the draft control damper shall be released from the open position and modulate as required by the draft setpoint. During normal burner shut-down the damper shall be driven open during the post-purge period and then closed when the fan stops. Abnormal burner shut-down (safety lock-out of flame safeguard control) shall cause the damper to drive open where it shall remain until the flame safeguard system is reset. The controller shall interconnect with the flame safeguard system directly using 120 VAC signals.
4. Draft Damper Modulation
When the precise draft control mode is required, the controller shall provide boiler outlet damper modulating control based on characterizable firing rate feed-forward signal to assure stable draft during load changes and “GAP” PID Draft Control for improved stability. Provide a Model SPS firing rate feedback potentiometer as manufactured by Preferred Instruments, Danbury, CT, or firing rate output from the firing rate controller. The controller shall be capable of establishing an adjustable position for burner light-off. Each fuel shall have an independent light-off position. The controller shall not close the light-off contact output unless the damper is above the proper position and the pressure is below the starting draft setpoint. Alternately, the controller shall be field selectable to provide “Floating” draft control. When “Floating” draft control is selected, the controller shall provide proportional control of the boiler outlet damper to maintain boiler draft at setpoint using a 24 VAC, Triac positioning output.
5. Draft Range Transmitter and High Pressure Switch
Provide a draft range transmitter and high pressure (low draft) switch with time delay relay. Both shall be supplied with field mountable, dust-tight, splash-proof enclosures. A single draft connection shall be piped to -1" W.C. to +1" W.C. 4-20 mADC transmitter and an independent low draft switch. The low draft switch setpoint shall be field adjustable from +0.15" W.C. to +4.0" W.C. The low draft switch shall be mounted and wired to a pilot light so as to illuminate when the low draft switch activates and to a 5 second time delay relay so as to provide an isolated “Low Draft Cut-Out”, 10 A contact for use in the Flame Safeguard Limit Circuit. The time delay feature helps avoid nuisance burner shutdowns due to momentary draft fluctuations.
6. Draft Damper Actuator (when required)
Provide an electric Draft Damper Actuator for each furnace. The actuator shall have adequate power to automatically position the damper and shall be suitable for control by the Draft Controller. The actuator shall be totally enclosed in a dust-tight housing; have integral, snap-action, travel limit and open proving switches, be capable of being stopped, started, or instantly reversed without loss of power or overloading. A double ended output shaft shall have an integral brake for precise positioning without backlash and rotate 90º in 30 seconds. When the precise draft control mode is selected, the actuator shall include an electrically isolated feedback potentiometer.
7. Draft Damper Assembly - Model E-Link (when required)
Provide a factory assembled stack damper assembly for each furnace. The draft damper shall be a dual opposed blade design, have 24" inside diameter [select from 12", 16", 20" or 24" diameter to match boiler outlet, consult factory for larger sizes], constructed of 10 gauge rolled steel. Non-opposed blade damper designs are not acceptable. Factory mount the draft damper actuator, draft range transmitter and time delayed, high pressure (low draft) cut-out assemblies (described in the above paragraphs) on the damper assembly. The damper actuator and damper assembly shall be stroked at the factory to ensure proper alignment. “Shipped Loose” components will not be accepted.
The Instrument shall include a RS485 Modbus network interface to communicate to a future Data Acquisition System (DAS) or Building Automation System (BAS).
9. Quality Assurance
The Instrument shall be manufactured and labeled in accordance with UL508 (CSA C22.2 #14 for use in Canada). Inspection and labeling shall be supervised by UL or other OSHA approved Nationally Recognized Test Lab (NRTL). The draft control system shall be a Preferred Instruments, Danbury, CT, Model JC-22D Draft Controller with Model JC-22XMTR Draft Range Transmitter Assembly or JC-22D Draft Controller and E-Link Draft Damper Assembly and Model SPS Shaft Position Sensor (when required).
DOCUMENTS & DOWNLOADS
|JC-22 Draft Controller Cutsheet (Catalog 25)|
|JC-22D, Furnace Draft Controller - Brochure|
|JC-22D, Draft Controller Installation Manual|
|JC-22D - Field Wiring Diagram For Upgrade|