Fuel Oil Specialties
Anti Syphon Valves
Model A, Anti-Syphon Valves - Installed in a vertical position at the highest point in the suction line with no part of the line between the valve and the tank below the maximum oil storage level. UL listed; Approved by the New York City Board of Standards and Appeals. Preferred Utilities' industrial factory is located in Danbury, CT (Connecticut).
Back Pressure Regulating Valves, Model BQ
Model BQ, Back Pressure Regulating Valves - Maintain constant supply pressure for generators, boilers, booster pumps, or any other application that requires constant oil pressure.
Back Pressure Regulating Valves, Model V
Model V, Back Pressure Regulating Valve - Installed at the far end of the oil supply line, down stream of the boiler fuel metering valves and passes unburned oil to the return line.
Rugged, maintenance-free terminal protection for breather lines from sumps, reservoirs, expansion tanks and a wide assortment of industrial applications. Preferred Utilities' industrial factory is located in Danbury, CT (Connecticut).
Double Poppet Foot Valves
Model 22, Double Poppet Foot Valve - Bronze body and poppet to provide long dependable service with light oils through #4 fuel oil.
Duplex Oil Strainers
Model 72, Duplex Oil Strainers - For duplex fuel oil handling systems and for those applications where the requirement for a continuous supply of oil does not permit interruption of the flow for the routine cleaning of strainer baskets.
Fire Safety Gas Shut-off Valves
Model 110-G, Fire Safety Gas Shut-off Valves - Used in any gas flow application by locating the valve in a horizontal pipe run where the gas supply enters the building.
For pumped filling of single or multiple tank systems
Uniform oil flow at different viscosities embodied in the Voluvalve and equalizing valve, integrated into one heated oil reservoir.
Foot Valve Extractor Fitting
Model 233-FV, Foot Valve Extractor Fitting - Permits easy removal and reinstallation of the Model 22 Double Poppet Foot Valves or Model 900 Single Poppet Foot Valves sizes smaller than 1½".
Four Inch Pressure Gauge
4" Pressure Gauge - The 4" pressure gauges are bottom connected with sealed stainless steel case and shatter-proof, heat resistant polycarbonate lenses.
Fusomatic Electric Cut-Off Switch
Fusomatic Electric Cut-Off Switch - The Fusomatic Electric Cut-Off Switch is a thermally actuated safety switch used in combustion installations. As required by many codes, it automatically breaks the burner control circuit in the event of a fire. Approved by The Massachusetts Department of Public Safety and Underwriters Laboratories Inc.
Fusomatic Globe / Gate Valves
Fusomatic Globe / Gate Valve - Thermally actuated safety switch used in combustion installations. As required by many codes, it automatically breaks the burner control circuit in the event of a fire. Approved by The Massachusetts Department of Public Safety
Ground Level Spill Containers
Model 1, Ground Level Spill Containers - Designed to catch any oil which can be spilled when disconnecting the delivery fitting during normal tank filling operations.
Horizontal Spill Containers
Model 2, Horizontal Spill Containers - Available in flush mounting, surface mounting and free standing arrangements.
Multi-Tank Gauge and Leak Detection System
Model TG-EL-D5 Multi-Tank Gauge and Leak Detection System - A comprehensive system that can simultaneously monitor product levels and leaks.
Oil Lever Gate Valves
Model 110, Spring Loaded Fire Safety Valves - Used in fuel oil piping systems to provide automatic shut-off of the fuel flow in the event of a fire. Valve operation is fully mechanical and is independent of the electrical power supply. The emergency fuel line shut-off is mandated by many codes.
Bi Metal Oil Thermometer - White dial with highly visible black numbers and pointer. The case is of welded stainless steel construction and is hermetically sealed to prevent the entrance of damaging moisture.
Overfill Prevention Valves
Model 71 & Model 61F-Stop, Overfill Prevention Valves - Provides a mechanical method of automatic fuel oil shut-off to prevent overfilling of underground storage tanks during a gravity filled delivery and above ground storage tanks during a pressurized fill (pump-in fill) delivery. It is designed to satisfy EPA regulations covering overfill protection, “a device that will automatically shut off the flow of oil into the tank when the tank is no more than 95% full.”
Pressure Reducing Valves
Model B, Pressure Regulating Valves - Installed in the supply line to boiler fuel metering valves. The valve senses down stream pressure to maintain a constant supply pressure to the fuel metering valves.
Model R, Relief Valves - Designed to relieve excess pressure in lines containing any grade of fuel oil. It is also suitable for use with water and air.
Simplex Oil Strainers
Model 125, Simplex Oil Strainers - Designed for applications where easy maintenance and large capacity straining are required. Service time is minimal because the cover is secured with quick opening, non-yoke type knobs.
Single Poppet Foot Valves
Model 60 Single Poppet Foot Valve - Installed at the end of suction lines at the bottom of fuel oil tanks to keep the suction line to the pump set primed by preventing the flow of oil back into the tank when the pumps are not in operation. Preferred Utilities' industrial factory is located in Danbury, CT (Connecticut).
Storage Tank Monitor Access Manhole
Model TG-MH-18, Storage Tank Monitor Access Manhole - Designed to set flush on a concrete pad at grade and provide access as required to equipment installed on an underground tank, such as tank gauging and leak detection equipment.
Tank Name Plates
The Preferred tank name plates are durable ⅛" thick cast-bronze plates with polished 1/16" high raised letters.
Tank Selector Valves
Tank Selector Valves, Threaded And Flanged Connections - Consists of a precision ground tapered plug which rotates 90 degrees within a precision machined cast iron body.
Tank Vent Bricks
Tank Vent Brick - Designed as a terminal for vent lines from storage tanks when the line is run inside the building walls. Approved by the New York City Board of Standars and Appeals.
Two-And-A-Half Inch Pressure Gauge
2.5" Pressure Gauge - The 2.5" pressure gauges are bottom connected with satin black steel case and shatterproof, heat resistant polycarbonate lenses.
Vacuum Breaker Valves
Model VB, Vacuum Breaker Valves - Assembly consists of a brass body with threaded ends, stainless steel ball and EPN “O” ring seat.
Standard Tank Vent Protectors - Made of cast aluminum or iron and are threaded for standard pipe connection. A wire mesh screen is included.
The Voluvalve utilizes a custom and proprietary drilled hole pattern inside the valve that allows the valve to repeatedly and accurately match the optimal efficiency flow rate and fuel-air ratio characteristics for any burner.
Watertight Flush Fill Caps
Model W, Watertight Flush Fill Cap - Assembly consists of a rust-resistant, galvanized cast iron body, with a gasket sealed solid bronze cover for a waterproof seal. Fill caps are available in 2", 3", and 4" NPT. Approved by The New York City Board of Standards and Appeals
Watertight Locking Fill Caps
Model FF, Watertight Locking Fill Cap - Assembly consists of a solid cast iron body with malleable iron hasp. The brass cover is gasketed to provide a waterproof seal. The body threads directly on to the line while the cap threads onto the body.
Flexible System Controller
Fuel Oil Transfer Pump Sets
Fuel Filtration Systems
Fuel Oil Heaters and Assemblies
Pump and Motor Assemblies
Fuel Oil Specialties
Diesel Fuel Oil Additives and Treatments
FIND A REP
PIPE SIZING CALCULATOR
FUEL LOAD CALCULATOR
FUEL SYSTEM SPECS
Join our mailing list